Please use the Selection Guide for combination of ESBE actuators and Controllers to ESBE valves.

For VRG valves we recommend to use actuators ARA600 series. However, besides valve type it is very important to know the correct control signal. Actuators can be driven by 2-point, 3-point or proportional signal and have a power supply of 24V or 230V. Most boiler controllers are using 3-point control signal with 230V power supply, but we highly recommend checking proper actuator parameters in boiler or controller manual.

!Disclaimer: 15sec actuator is not applicable on DN40/50

- Set the valve in midposition. Examples are in the valve user instruction
- Assembly the actuator on the valve according to actuator user instruction
- Power up the actuator first after you are sure about correct assembling

The actuators and valves are always delivered in midposition from ESBE.

If the actuator is not in midposition
- Set the actuator in manual mode and set in midposition
- Assembly the actuator on the valve
- Change the actuator back to originale position and set in automatic mode

Follow these steps:

1. Actuator: Activate manual operation mode and turn the knob (= the gear box) to the mid-position.
2. Actuator: Remove the knob by pulling it out from the controller. Make sure to not rotate the position set in point 1 during removal.
3. Valve: Turn the mixing valve to mid-position (desired) and assemble the adaptor kit.
4. Actuator: Assemble the actuator to the valve and fix it with the M5 bolt.
5. Actuator: Re-place the knob on the actuator and gently push it down as you rotate the knob to find its correct position.

No, this is not possible. We recommend replacing the actuator together with the valve to secure an optimal operation. Suitable actuator is found in our replacement guide that is available in the “Support” section.

Check that the valve and actuator are correct assembled together, more information regarding different applications and how to assembly can be found in the User instruction or on this web site.

There could be several reasons why the actuator is going back and forth:
- Check that the signal to the actuator is correct and without any disturbance
- Check if the valve is oversized by calculating the needed KVs value in your system. Calculation can be made in ESBE Hydronic Selection software that is available on this web site.

The microswitch can be used to connect external equipment that you would like to start/stop by the valve position. Example could be circulation pump that you would like to turn of if the valve is closed. Another example can be auxiliary heat that you would like to turn on when the valve reach a specific valve postion.

- Check that the valve and actuator are correct assembled together, more information regarding different applications and how to assembly can be found in the User instruction. The User instruction is available on the Product page and the folder "Download Area"
-Check that the knob of the ARA is not in manual position. See pictures below.

 

With the green adjusting cam you are changing when the auxiliary switch will be activated/deactivated.

By swapping the black and brown cable during installation you can change the working direction.

By shifting the jumpers/brackets on the circuit board, e.g. from horizontal to vertical.

See the instructions manual in the packaging, or on our website for more information.

On/off on dip switch 6 - ARA639

On/off on dip switch 2 – ARA659

  

Please see User instruction for more detailed information

Yes, it is possible. Series 90 actuators with 3-point and 2-point control signal has a settable operating range between 30 up to 180°, the type 95-270M up to 270°.

For the proportional versions the settable operating range is:
- between 30-90º for version 92P
- between 30-180º for version 92P2
- between 180-355º for version 92P4

Please note, this feature is not made for adjusting the actuator to a wrongly adjusted valve.  All ESBE actuators and controllers (not the 92P4) are delivered in the mid position.  Before the actuator is mounted, please set also the valve in mid position.

Yes, it is possible. Please use Adaptor kit VRG801 with article number 16053300.